Leather card holder pattern
The pattern is computed from your card. For a standard 85.6 × 54 mm (3 3/8 × 2 1/8 in) card held sideways, the Custom card holder cuts every layer 105 mm (4 1/8 in) wide, the front pocket 53 mm (2 1/16 in) tall and, with two pockets per side, the back panel 80 mm (3 1/8 in) tall. Pick one of 6 styles, 1 to 3 pockets per side, and cards sideways or upright.

Sizes by pocket count
| Cards | Width | Front pocket | Back panel | Stitch holes |
|---|---|---|---|---|
| Sideways, 1 pocket per side | 105 mm (4 1/8 in) | 53 mm (2 1/16 in) | 70 mm (2 3/4 in) | 82 |
| Sideways, 2 pockets per side | 105 mm (4 1/8 in) | 53 mm (2 1/16 in) | 80 mm (3 1/8 in) | 114 |
| Sideways, 3 pockets per side | 105 mm (4 1/8 in) | 53 mm (2 1/16 in) | 91 mm (3 9/16 in) | 146 |
| Upright, 1 pocket per side | 75 mm (2 15/16 in) | 84.6 mm (3 5/16 in) | 101.6 mm (4 in) | 98 |
| Upright, 2 pockets per side | 75 mm (2 15/16 in) | 84.6 mm (3 5/16 in) | 111.6 mm (4 3/8 in) | 122 |
| Upright, 3 pockets per side | 75 mm (2 15/16 in) | 84.6 mm (3 5/16 in) | 122.6 mm (4 13/16 in) | 146 |
Width is every layer's width; heights are measured up from the bottom edge. Stitch holes: every layer together, at the default stitch spacing. Enter your own card size in the Studio.
Six ways to build it
Each style below is drawn by the engine at the default card and leather. The cut sizes are the outline of each piece.
Layered
A back panel with stacked pockets, sewn around the outside.

Back panel: 105 × 80 mm (4 1/8 × 3 1/8 in), 59 stitch holes; Pocket 1 (outermost): 105 × 53 mm (4 1/8 × 2 1/16 in), 38 stitch holes; Card slot 2 (next to back panel): 105 × 53 mm (4 1/8 × 2 1/16 in), 17 stitch holes Flap with snap
The back panel runs on into a flap that folds over the front pocket and closes with a snap.

Back panel: 105 × 146.5 mm (4 1/8 × 5 3/4 in), 55 stitch holes, 1 fold line; Pocket 1 (outermost): 105 × 53 mm (4 1/8 × 2 1/16 in), 38 stitch holes; Card slot 2 (next to back panel): 105 × 53 mm (4 1/8 × 2 1/16 in), 17 stitch holes Bands
One long back panel with leather bands sewn across it; the cards slide under the bands.

Back panel: 105 × 180 mm (4 1/8 × 7 1/16 in), 70 stitch holes; Band 1: 105 × 12 mm (4 1/8 × 1/2 in), 4 stitch holes; Band 2: 105 × 12 mm (4 1/8 × 1/2 in), 4 stitch holes Side-entry
A wallet that folds in the middle, with two card columns; pockets open toward the fold or at the top.

Back panel: 165.8 × 106.6 mm (6 1/2 × 4 3/16 in), 110 stitch holes, 1 fold line; Left pocket 1 (front, opens toward the fold): 60 × 106.6 mm (2 3/8 × 4 3/16 in), 41 stitch holes; Left pocket 2 (opens toward the fold): 75 × 106.6 mm (2 15/16 × 4 3/16 in), 47 stitch holes; Right pocket 1 (front, opens at the top): 75 × 84.6 mm (2 15/16 × 3 5/16 in), 45 stitch holes; Right pocket 2 (opens toward the fold): 75 × 106.6 mm (2 15/16 × 4 3/16 in), 63 stitch holes Folded pocket
One piece folded in half and sewn along its open edges.

Folded pocket: 105 × 100.2 mm (4 1/8 × 3 15/16 in), 36 stitch holes, 1 fold line Folded slim wallet
One piece of three panels: fold the side panel behind, then the bottom panel up behind it, and sew the closed edge.

Slim wallet: 209.4 × 102.4 mm (8 1/4 × 4 1/16 in), 26 stitch holes, 2 fold lines
Folded styles and leather thickness
A fold uses length, and thicker leather uses more. In the folded styles the engine sizes the folded piece for your leather, so the same holder is cut to slightly different sizes in thin and in thick leather.
| Style (folded piece) | 0.8 mm (2 oz) | 1.4 mm (3.5 oz) | 2.0 mm (5 oz) |
|---|---|---|---|
| Flap with snap (back panel) | 105 × 143.7 mm (4 1/8 × 5 5/8 in) | 105 × 146.5 mm (4 1/8 × 5 3/4 in) | 105 × 149.3 mm (4 1/8 × 5 7/8 in) |
| Side-entry (back panel) | 161.1 × 106.6 mm (6 5/16 × 4 3/16 in) | 165.8 × 106.6 mm (6 1/2 × 4 3/16 in) | 170.5 × 106.6 mm (6 11/16 × 4 3/16 in) |
| Folded pocket | 105 × 99.3 mm (4 1/8 × 3 15/16 in) | 105 × 100.2 mm (4 1/8 × 3 15/16 in) | 105 × 101.1 mm (4 1/8 × 4 in) |
| Folded slim wallet (slim wallet) | 209.7 × 100.5 mm (8 1/4 × 3 15/16 in) | 209.4 × 102.4 mm (8 1/4 × 4 1/16 in) | 209.1 × 104.3 mm (8 1/4 × 4 1/8 in) |
Width × height of the piece that carries the fold lines, at the default card and one card per pocket.
Stitching
- Stitch spacing
- 5 mm by default, holes 0.9 mm across
- Distance from edge
- 4 mm inside every cut edge of the seam
- Leather
- Pockets in leather up to 1.2 mm (3 oz) keep the edge thin. The folded styles take 0.8 mm to 2.0 mm and start at 1.4 mm (3.5 oz).
Two versions
- Card holder · Custom
- Every setting: 1–3 pockets per side, 6 styles and 19 pocket edge shapes. The numbers on this page are from this version.
- Card holder · Classic
- The traditional card holder: just your card size and one of 4 pocket edges.
Before you cut
Make your card holder
Enter your card size, pick a style and the number of pockets, and the pattern is drawn as you go. The download has a printable PDF (US Letter or A4) and SVG and DXF files.
- Open Card holder · CustomEvery setting: 1–3 pockets per side, 6 styles and 19 pocket edge shapes.
- Open Card holder · ClassicThe traditional card holder: just your card size and one of 4 pocket edges.
Questions
How wide should a leather card holder be?
For a standard 85.6 mm card held sideways, 105 mm (4 1/8 in): the card plus 4 mm to the stitching and 5.7 mm of room on each side. Held upright, 75 mm (2 15/16 in).
How tall is the back panel?
With the card sideways: 70 mm with 1 pocket per side, 80 mm with 2 pockets per side, 91 mm with 3 pockets per side. The front pocket stays 53 mm tall, so 5 mm of the card shows above it.
Can I use it for other cards?
Yes. Enter your card's size, from 80 mm to 92 mm wide and 48 mm to 60 mm tall; every piece is computed again.
Can I cut it with a laser?
Yes, after a cleanup. The SVG and DXF are true-scale files of the pattern sheet: keep the piece outlines and the holes, and delete the labels, test squares and guide lines before cutting.
Guides
Numbers from Card holder · Custom, pattern version 5.0.1, at the default settings. Updated October 27, 2026.
