Classic card holder
The traditional card holder: just your card size and one of 4 pocket edges.
Leather card holder pattern
Pick a starting point. You can change every size in the next step.
The traditional card holder: just your card size and one of 4 pocket edges.
Two stacked pockets with one smooth dip across the top.
Pockets on both faces with an off-center V opening, and a center pocket between the two backs.
Upright, with two pockets, a round thumb notch and a half-round push-out cut at the bottom.
The back panel runs on into a flap that folds over the front pocket and closes with a snap.
One piece of three panels, folded twice and sewn along the closed edge.
The everyday holder: two stacked pockets with a curved opening on one face.
A pocket and a card slot on each face with straight openings, and a center pocket between the backs.
Four pockets and a center pocket, each opening dipping in a curve.
Four pockets and a center pocket, each opening with a slanted thumb notch.
Upright, one pocket on each face with a straight opening, and a center pocket between the backs.
Upright, a curved-opening pocket on each face and a center pocket.
Upright, a pocket with a slanted thumb notch on each face and a center pocket.
Upright and two-sided, with a U slot cut up from the bottom of the front pocket to push cards out.
The U push-up slot on the front pocket, with slanted thumb-notch openings.
The U push-up slot on the front pocket, with gently arched openings.
A pocket and a card slot in front; a plain back left open on one side, so the back pocket opens at the top and the side.
One piece of three panels folded twice, standing upright, with a deep V thumb notch at the fold.
Upright, three pockets under a flap with scooped shoulders that closes with a snap.
One long back panel with a thumb notch and waist notches; two bands sewn into the side seams hold the cards.
Folds at a spine: side-entry pockets opening toward the fold on the left, a top pocket over a full pocket on the right.
Folds at a spine, with side-entry pockets opening toward the fold on both halves.
Folds at a spine, with top-entry pockets and round thumb notches on both halves.
One curved pocket on each face, a center pocket, and a half-round push-out on the front pocket.
A lens-shaped pocket over a thumb-notch slot in front, and a plain back sewn all round for a center pocket.
One strip folded at the bottom, scooped at the top, with a push-out hole on the fold.
One piece folded at a side, rounded at the top, with a chamfered bottom corner; sewn along the open side and the bottom.
Upright, an outer pocket and two card slots on one face, with straight openings.
Upright, three stacked pockets with shallow curved openings.
Upright, three stacked pockets whose openings slope down to the right.
Upright, three stacked pockets whose openings slope down to the left.
Upright, two stacked pockets on each side and a center pocket between.
Three stepped pockets on the front, a plain back and a center pocket between the panels.
Two pockets; the front pocket has a window so the card behind shows through.
Two pockets a side with diagonal openings and a center pocket.
V openings on both sides and a tapered push-out cut in the bottom edge.
Straight openings on both sides and a wide, shallow push-out along the bottom edge.
A full front pocket and a card-wide inset slot behind it.
A full front pocket and two card-wide inset slots stepped behind it.
Inset slots behind the front pocket on both sides, with a center pocket.
Two full-width pockets; the back one has a raised floor so its card shows.
Three full-width pockets with raised floors and a round thumb cut.
Two pockets as tall as the back panel, with scooped openings for the cards.
One pocket as tall as the back panel, with a deep V opening.
Two pockets; the front pocket rises to the top on the left.
Every setting: 1–3 pockets per side, 6 styles and 19 pocket edge shapes.
Showing 45 of 45 styles
New to card holders? Read how to make a leather card holder or see every card holder style.