22 mm leather watch strap pattern

A 22 mm strap tapers to a 20 mm buckle. At the default size the long strap is 115 mm (4 1/2 in) from the spring bar to the tip and the short strap 75 mm (2 15/16 in) from the spring bar to the buckle bar. With the folded ends included you cut the long top 132.6 mm (5 1/4 in) and the short top 127.1 mm (5 in). The folds use 5.9 mm (1/4 in) at the buckle and 4.3 mm (3/16 in) at each spring bar, computed from 1.2 mm (3 oz) leather and the bar sizes below.

Pattern pieces of the 22 mm leather watch strap at the default settings: Long strap - top, Long strap - lining, Short strap - top, Short strap - lining, Fixed keeper and Free keeper
The pieces at the default settings, drawn by the pattern engine at this lug width. The Studio makes the full-size pattern.

Cut list

Cut list at the default settings (lined, flat)
PieceLeatherCut length × widthStitch holes
Long strap - topTop leather, 1.2 mm (3 oz)132.6 × 22 mm (5 1/4 × 7/8 in)101 + 7 adjustment
Long strap - liningLining, 1.0 mm (2.5 oz)112.4 × 22 mm (4 7/16 × 7/8 in)88 + 7 adjustment
Short strap - topTop leather, 1.2 mm (3 oz)127.1 × 22 mm (5 × 7/8 in)86
Short strap - liningLining, 1.0 mm (2.5 oz)56.8 × 22 mm (2 1/4 × 7/8 in)49
Fixed keeperKeeper leather, 1.0 mm (2.5 oz)60.9 × 6 mm (2 3/8 × 1/4 in)4
Free keeperKeeper leather, 1.0 mm (2.5 oz)63.9 × 5 mm (2 1/2 × 3/16 in)4

Lengths run along the strap and include the folded ends; width is the widest point.

Folds at the buckle and spring bars

Leather used by each fold, and the turnback you cut
EndBar acrossLeather at the foldFold allowanceTurnback cut, length × width
Buckle end (short strap)2 mm (play 0.15 mm)1.0 mm5.9 mm (1/4 in)34.3 × 20 mm (1 3/8 × 13/16 in)
Spring-bar end, short strap1.5 mm (play 0.10 mm)1.0 mm4.3 mm (3/16 in)17.8 × 22 mm (11/16 × 7/8 in)
Spring-bar end, long strap1.5 mm (play 0.10 mm)1.0 mm4.3 mm (3/16 in)17.6 × 22 mm (11/16 × 7/8 in)

Turnback: on the flat piece, from the bar's center line to the tail's end. Fold allowances do not change with the width. How the fold allowance is worked out.

Hardware and keepers

Buckle
20 mm wide (the strap's width at the buckle)
Buckle bar and tongue
Bar 2 mm across, tongue wire 1.8 mm. Check yours with calipers: buckles are not standardized.
Spring bars
1.5 mm across. Measure yours with calipers.
Tongue slot
13.1 mm long, 3 mm wide
Fixed keeper
6 mm wide, cut 60.9 mm (2 3/8 in) long
Free keeper
5 mm wide, cut 63.9 mm (2 1/2 in) long

Holes

Adjustment holes
7 round holes, 2 mm across, 7 mm apart; the first 20 mm (13/16 in) from the tip
Stitch spacing
2.77 mm (short strap) and 2.71 mm (long strap), evened out along the edges for a 2.70 mm pricking iron; the Studio can also space them exactly at the iron's spacing.
Edge stitch holes
42 holes on the short strap, 83 holes on the long strap (both edges)
Rows across the strap
short strap: 5 holes at the spring bar, two rows of 4 holes at the buckle end; long strap: 5 holes at the spring bar
Every stitch hole you punch
332 holes in all pieces together, each layer punched before gluing

Next to the sizes either side

This width and its neighbors, at the default settings
Lug widthBuckleFixed keeper cutFree keeper cutTongue slot widthStitch holes
20 mm18 mm56.9 mm (2 1/4 in)59.9 mm (2 3/8 in)2.5 mm321
22 mm (this page)20 mm60.9 mm (2 3/8 in)63.9 mm (2 1/2 in)3 mm332
24 mm22 mm64.9 mm (2 9/16 in)67.9 mm (2 11/16 in)3 mm342

Going from 22 mm to 20 mm takes 4 mm off the fixed keeper (60.9 mm → 56.9 mm) and removes 11 stitch holes (332 → 321); the buckle goes from 20 mm to 18 mm.

Going from 22 mm to 24 mm adds 4 mm to the fixed keeper (60.9 mm → 64.9 mm) and adds 10 stitch holes (332 → 342); the buckle goes from 20 mm to 22 mm.

Before you cut

Not yet confirmed in leather: we made this strap in paper and in leather from an earlier file of this version (22 mm lug, 20 mm buckle, lined, flat). Since then we changed the buckle end, the keeper zone, the short lining, the padding and the stitch and hole options, and checked those changes in software only, so today's files have not been built in leather. The folds at both ends are computed from the leather thickness and bar sizes you enter, so check yours with calipers. Before you cut your good leather, mock up the folded ends in scrap leather of the same thickness, around your real buckle and spring bar.

The fold model behind these numbers is checked in software. Computed for 1.2 mm (3 oz) top leather and a 1.0 mm (2.5 oz) lining.

Make this strap

These numbers are Watch strap · Custom at 22 mm × 20 mm: in the Studio set Lug width to 22 mm and Buckle width to 20 mm, then enter your leather and spring bar.

Questions about this size

What buckle fits a 22 mm strap?

This pattern tapers from 22 mm at the lugs to 20 mm at the buckle, so it takes a 20 mm buckle. For a straight strap, set Buckle width to 22 mm in the Studio. The buckle end is computed for a 2 mm buckle bar; check yours with calipers.

How long do I cut the leather for a 22 mm strap?

Cut the long top 132.6 mm (5 1/4 in) and the short top 127.1 mm (5 in), both 22 mm at their widest. These lengths include the folded ends around the spring bars and the buckle bar, for finished straps of 115 mm and 75 mm.

How long are the keepers for a 22 mm strap?

Cut the fixed keeper 60.9 mm (2 3/8 in) long and 6 mm wide, and cut the free keeper 63.9 mm (2 1/2 in) long and 5 mm wide. Each is a loop closed with a 7 mm stitched lap.

How many stitch holes are there?

42 holes along the edges of the short strap and 83 holes along the long strap, for a 2.70 mm pricking iron. Counting every layer and both keepers you punch 332 holes.

Does it print on US Letter?

The pattern prints on 2 pages of US Letter or A4: a Start here page with a 50 mm and a 2 in test square, then the pattern. Print at 100 % and measure the 50 mm square before you cut.

Numbers from Watch strap · Custom, pattern version 2.0.1 (engine 2.0.0), at the default settings. Updated October 27, 2026.