20 mm leather watch strap pattern
A 20 mm strap tapers to an 18 mm buckle. At the default size the long strap is 115 mm (4 1/2 in) from the spring bar to the tip and the short strap 75 mm (2 15/16 in) from the spring bar to the buckle bar. With the folded ends included you cut the long top 132.6 mm (5 1/4 in) and the short top 127.1 mm (5 in). The folds use 5.9 mm (1/4 in) at the buckle and 4.3 mm (3/16 in) at each spring bar, computed from 1.2 mm (3 oz) leather and the bar sizes below.

Cut list
| Piece | Leather | Cut length × width | Stitch holes |
|---|---|---|---|
| Long strap - top | Top leather, 1.2 mm (3 oz) | 132.6 × 20 mm (5 1/4 × 13/16 in) | 99 + 7 adjustment |
| Long strap - lining | Lining, 1.0 mm (2.5 oz) | 112.4 × 20 mm (4 7/16 × 13/16 in) | 87 + 7 adjustment |
| Short strap - top | Top leather, 1.2 mm (3 oz) | 127.1 × 20 mm (5 × 13/16 in) | 80 |
| Short strap - lining | Lining, 1.0 mm (2.5 oz) | 56.8 × 20 mm (2 1/4 × 13/16 in) | 47 |
| Fixed keeper | Keeper leather, 1.0 mm (2.5 oz) | 56.9 × 6 mm (2 1/4 × 1/4 in) | 4 |
| Free keeper | Keeper leather, 1.0 mm (2.5 oz) | 59.9 × 5 mm (2 3/8 × 3/16 in) | 4 |
Lengths run along the strap and include the folded ends; width is the widest point.
Folds at the buckle and spring bars
| End | Bar across | Leather at the fold | Fold allowance | Turnback cut, length × width |
|---|---|---|---|---|
| Buckle end (short strap) | 2 mm (play 0.15 mm) | 1.0 mm | 5.9 mm (1/4 in) | 34.3 × 18 mm (1 3/8 × 11/16 in) |
| Spring-bar end, short strap | 1.5 mm (play 0.10 mm) | 1.0 mm | 4.3 mm (3/16 in) | 17.8 × 20 mm (11/16 × 13/16 in) |
| Spring-bar end, long strap | 1.5 mm (play 0.10 mm) | 1.0 mm | 4.3 mm (3/16 in) | 17.6 × 20 mm (11/16 × 13/16 in) |
Turnback: on the flat piece, from the bar's center line to the tail's end. Fold allowances do not change with the width. How the fold allowance is worked out.
Hardware and keepers
- Buckle
- 18 mm wide (the strap's width at the buckle)
- Buckle bar and tongue
- Bar 2 mm across, tongue wire 1.8 mm. Check yours with calipers: buckles are not standardized.
- Spring bars
- 1.5 mm across. Measure yours with calipers.
- Tongue slot
- 13.1 mm long, 2.5 mm wide
- Fixed keeper
- 6 mm wide, cut 56.9 mm (2 1/4 in) long
- Free keeper
- 5 mm wide, cut 59.9 mm (2 3/8 in) long
Holes
- Adjustment holes
- 7 round holes, 2 mm across, 7 mm apart; the first 20 mm (13/16 in) from the tip
- Stitch spacing
- 2.77 mm (short strap) and 2.70 mm (long strap), evened out along the edges for a 2.70 mm pricking iron; the Studio can also space them exactly at the iron's spacing.
- Edge stitch holes
- 42 holes on the short strap, 83 holes on the long strap (both edges)
- Rows across the strap
- short strap: 4 holes at the spring bar, two rows of 3 holes at the buckle end; long strap: 4 holes at the spring bar
- Every stitch hole you punch
- 321 holes in all pieces together, each layer punched before gluing
Next to the sizes either side
| Lug width | Buckle | Fixed keeper cut | Free keeper cut | Tongue slot width | Stitch holes |
|---|---|---|---|---|---|
| 18 mm | 16 mm | 52.9 mm (2 1/16 in) | 55.9 mm (2 3/16 in) | 2.5 mm | 315 |
| 20 mm (this page) | 18 mm | 56.9 mm (2 1/4 in) | 59.9 mm (2 3/8 in) | 2.5 mm | 321 |
| 22 mm | 20 mm | 60.9 mm (2 3/8 in) | 63.9 mm (2 1/2 in) | 3 mm | 332 |
Going from 20 mm to 18 mm takes 4 mm off the fixed keeper (56.9 mm → 52.9 mm) and removes 6 stitch holes (321 → 315); the buckle goes from 18 mm to 16 mm.
Going from 20 mm to 22 mm adds 4 mm to the fixed keeper (56.9 mm → 60.9 mm) and adds 11 stitch holes (321 → 332); the buckle goes from 18 mm to 20 mm.
Before you cut
The fold model behind these numbers is checked in software. Computed for 1.2 mm (3 oz) top leather and a 1.0 mm (2.5 oz) lining.
Make this strap
These numbers are Watch strap · Custom at 20 mm × 18 mm: in the Studio set Lug width to 20 mm and Buckle width to 18 mm, then enter your leather and spring bar.
- Open Watch strap · CustomEvery setting: lined or single layer, padding, hole shapes and stitching.
- Open Watch strap · ClassicThe traditional lined strap with only the essentials: width, size and tip.
Questions about this size
What buckle fits a 20 mm strap?
This pattern tapers from 20 mm at the lugs to 18 mm at the buckle, so it takes an 18 mm buckle. For a straight strap, set Buckle width to 20 mm in the Studio. The buckle end is computed for a 2 mm buckle bar; check yours with calipers.
How long do I cut the leather for a 20 mm strap?
Cut the long top 132.6 mm (5 1/4 in) and the short top 127.1 mm (5 in), both 20 mm at their widest. These lengths include the folded ends around the spring bars and the buckle bar, for finished straps of 115 mm and 75 mm.
How long are the keepers for a 20 mm strap?
Cut the fixed keeper 56.9 mm (2 1/4 in) long and 6 mm wide, and cut the free keeper 59.9 mm (2 3/8 in) long and 5 mm wide. Each is a loop closed with a 7 mm stitched lap.
How many stitch holes are there?
42 holes along the edges of the short strap and 83 holes along the long strap, for a 2.70 mm pricking iron. Counting every layer and both keepers you punch 321 holes.
Does it print on US Letter?
The pattern prints on 2 pages of US Letter or A4: a Start here page with a 50 mm and a 2 in test square, then the pattern. Print at 100 % and measure the 50 mm square before you cut.
Other sizes and guides
Numbers from Watch strap · Custom, pattern version 2.0.1 (engine 2.0.0), at the default settings. Updated October 27, 2026.
