Watch strap length by wrist size: how long the two pieces should be
A two-piece watch strap is quoted as two lengths measured from the spring bar, 115/75 mm for the common medium: the long side to its tip and the short side to the buckle bar, buckle not included. That medium is 115 mm (4 1/2 in) long and 75 mm (2 15/16 in) short. Sizes run from about 95/60 for a small wrist to 140/95 for a large one. Below: the size table our generator offers, how to measure a wrist and turn it into a size, and why the watch case changes the answer.
How strap lengths are measured
Makers quote the finished length of each piece from the center of the spring bar. The long piece (the one with the holes) is measured to the tip. The short piece (the one with the buckle) is measured to the center of the buckle bar, so the buckle itself is not counted. A 115/75 strap therefore spans 190 mm plus the buckle, before it is buckled.
The pattern pieces are longer than these numbers, because each end wraps a bar and is glued back on itself. On our default 22 mm strap the long piece is cut 132.6 mm for a finished 115 mm, and the short piece 127.1 mm for a finished 75 mm. Keep that in mind when you compare a pattern to a strap you own: measure the finished strap, not the flat leather.
Strap sizes from XS to XL
There is no industry standard for S, M and L, and two makers' mediums differ by a few millimeters. The table is the set of sizes our generator offers, drawn from published maker size charts; each row sets both lengths together.
| Size | Long piece | Short piece | Both pieces |
|---|---|---|---|
| XS | 95 mm (3 3/4 in) | 60 mm (2 3/8 in) | 155 mm |
| S | 105 mm (4 1/8 in) | 70 mm (2 3/4 in) | 175 mm |
| M | 115 mm (4 1/2 in) | 70 mm (2 3/4 in) | 185 mm |
| M | 115 mm (4 1/2 in) | 75 mm (2 15/16 in) | 190 mm |
| L | 125 mm (4 15/16 in) | 75 mm (2 15/16 in) | 200 mm |
| L | 128 mm (5 1/16 in) | 85 mm (3 3/8 in) | 213 mm |
| XL | 140 mm (5 1/2 in) | 95 mm (3 3/4 in) | 235 mm |
Lengths from the spring bar, buckle not included. Two mediums and two larges exist because makers' charts differ; pick the one closer to a strap that fits you. The generator also accepts any length from 90 to 160 mm long and 55 to 105 mm short.

Measure the wrist and pick a size
Wrap a soft tape, or a strip of paper you then lay on a ruler, around the wrist where the watch sits, snug but not tight. Note the number in centimeters or inches. Then account for the watch, because the case itself bridges part of the wrist: a strap that fits a 40 mm watch is too long on a 34 mm watch with the same wrist.
- Measure the wrist as above.
- Measure the watch from lug tip to lug tip, the long way across the dial. This is the part of the wrist the case covers.
- The strap must cover the rest: wrist minus the lug-to-lug span, plus the length that goes through the buckle and under the keepers (about 20 to 25 mm) so the tip is held.
- Pick the preset whose two lengths added together come closest, with the long piece doing the adjusting: the middle hole should land on the buckle at your wrist size.
As a rough guide from makers' charts: a wrist around 15 to 17 cm (6 to 6¾ in) sits in S, 16.5 to 19 cm (6½ to 7½ in) in M, 18.5 to 21 cm (7¼ to 8¼ in) in L. The overlaps are real, which is why the middle hole matters more than the label. If you are between two sizes, take the longer one; a long piece is easy to shorten at the tip before the holes are punched, a short one cannot be lengthened.
The adjustment holes
The long piece carries the holes the buckle's tongue goes through. Our default is 7 holes of 2 mm at 7 mm spacing, the first 20 mm from the tip, which gives 42 mm of adjustment. The generator accepts 1 to 12 holes at 6 to 10 mm, and keeps the last hole clear of the lug end so the strap is never buckled onto its own fold.
When the middle hole is the one you use, the strap has three holes of room either way: about 21 mm, or the difference between a winter wrist and a summer one. If you always use the first or last hole, the strap is the wrong size; change the preset rather than punching an extra hole near the fold.
A strap for one wrist
If the strap is for one person, measure and skip the presets. Enter the long and short lengths directly in the generator; the pieces, folds and holes are drawn for them. For a lady's watch or a child, go toward 95/60; for a very large wrist or a thick case, toward 140/95. The buckle end rarely needs to change; the long piece does most of the work.
Draw the strap at your length
Pick a size preset or type the two lengths, then the lug width and your leather and bars; the pieces are drawn with the folds and the 7 holes in place.
- Open Watch strap · CustomEvery setting: lined or single layer, padding, hole shapes and stitching.
- Open Watch strap · ClassicThe traditional lined strap with only the essentials: width, size and tip.
Questions
What is the standard watch strap length?
There is no standard, but 115/75 mm (long piece 115 mm, short piece 75 mm, both from the spring bar) is the common medium and our default. Makers' mediums run from about 115/70 to 120/75.
How is a watch strap's length measured?
From the center of the spring bar: the long piece to its tip, the short piece to the center of the buckle bar. The buckle is not included. Measure a finished strap, not the flat leather, which is longer because of the folds.
What watch strap length for a 7 inch wrist?
A 7 in (17.8 cm) wrist is usually a medium, 115/75, on a watch around 40 mm. On a smaller watch, or if the middle hole ends up at the end of the strap, move to the longer medium or to L.
How many holes should a watch strap have?
Our default is 7 holes at 7 mm spacing, the first 20 mm from the tip; makers use 6 to 10 holes at 6 to 8 mm. More holes do not make a strap fit better; the right length does.
Related
Numbers from the watch strap engine (pattern version 2.0.1). Updated October 25, 2026. More guides.
